A-190-1 Midi-to-CV/Gate/Sync Interface

130 

MIDI-to-CV/Gate/Sync Interface

 

 

 

Available on backorder

Add to Wishlist
Add to Wishlist
Estimated delivery 21 days
Category: Tags: , , , ,

Description

Module A-190 is a MIDI-CV/SYNC Interface, with which you can control any A-100 Module which has CV and gate/trigger input sockets by MIDI. The A-190 has two Digital-to-Analogue converters (DAC for short), which put out control voltages from 0 V to +5 V, so that you can control not just the pitch, but also another voltage-controllable parameter on the A-100. DAC 1 is ‘hard-wired’ to receive MIDI note messages and convert them into control voltages available at CV output socket CV 1. The DAC has 12-bit resolution, which gives excellent tuning resolution (in steps of 1/4096th). As a rule, DAC 1 will be used to control VCO pitch. DAC 2 can be assigned to your choice of MIDI controller. This DAC has 7-bit resolution (1/128th steps). Its output is available at CV 2, and can be used for voltage control of any suitable module (eg VCF, VCA, etc.). The Gate output has 0/+12V voltage level.
The A-190 also has a clock output (0/+5V level), controlled by MIDI clock. This can be divided down to provide a variety of clock outputs, and enable older sequencers or drum machines to be synced to MIDI. A Reset Output (0/+5V level) provides control of the A-160 / 161 Clock Divider / Sequencer or can produce MIDI-synchronised gates (for instance on an ADSR). MIDI START or CONTINUE messages make the voltage at the Reset output go low, and MIDI STOP messages make it go high.
In addition, the A-190 allows for portamento (glide) and pitch-bend, and provides a software LFO. These functions can all be switched on and off or altered by MIDI controllers. All control parameters can be saved in non-volatile memory.

For more detailed information please look at the English user’s guide: A190_man.pdf

Attention: A-190 requires an additional +5V power supply with 50mA e.g. the low-cost 5V adapter !

Remark: The A-190 has been renamed to A-190-1 to distinguish it better from the low-cost Midi-CV/Gate interface A-190-2

Module A-190-1will be replaced from about spring 2014 by the new module A-190-4. The functions of A-190-1 and A-190-4 are nearly the same (Midi In, Midi Out, CV1, CV2, Gate, Clock, Reset). But the operation of the A-190-4 has been improved because a 3-digit LED display is available. The current values of all parameters (like Midi channel, reference note, clock divider) can be read back and modified by means of up/down buttons. In addition A-190-4 is equipped with an USB interface and the external +5V supply is no longer available. The module width is the same for A-190-1 and A-190-4.

 

Width: 10 HP / 50.5 mm

Depth:: 95mm (measured from the rear side of the front panel)
Current: +10mA (+12V) / -0mA (-12V)

Attention: A-190 requires the additional +5V power supply !

 

 

 

Specifications

brand

Doepfer

Reviews

There are no reviews yet.

Be the first to review “A-190-1 Midi-to-CV/Gate/Sync Interface”

Your email address will not be published. Required fields are marked *

Search machineroom.com.ua

Login

Create an account

Your personal data will be used to support your experience throughout this website, to manage access to your account, and for other reasons described in our privacy policy.

Password Recovery

Lost your password? Please enter your username or email address. You will receive a link to create a new password via email.

SHOPPING BAG (0)

A-190-1 Midi-to-CV/Gate/Sync Interface

130 

Available on backorder